The principle of shell-and-tube evaporators
22-09-21
The shell-and-tube evaporator is fabricated by forming two layers of metal sheets through high-pressure gas expansion or mechanical stamping. It can also be produced by die-casting using magnesium-aluminum alloy. This type of evaporator is widely used in small refrigeration appliances such as refrigerators, display cabinets, and ice-cream storage boxes. The flat-tube evaporator made from magnesium-aluminum alloy die-cast is extensively employed in contact freezing applications and is commonly referred to as a flat-tube rapid condenser. Now, let’s take a closer look at the operating principle of the shell-and-tube evaporator!

The heat transfer coefficient of a shell-and-tube evaporator is higher in liquids than in gases, and higher under flowing conditions than under stationary conditions.
Shell-and-tube evaporators offer excellent heat transfer performance, a compact structure, a small footprint, and easy installation, making them widely used in various applications. The structure of the water-tank evaporator is identical to that of a horizontal shell-and-tube condenser. To maintain an appropriate flow rate, the refrigerant carrier enters from the lower part of the end cover and exits from the upper part, circulating back and forth inside the evaporating tubes and within the end covers, thus creating multiple flow paths. On the other hand, the refrigerant flows outside the tubes; after throttling, the liquid refrigerant enters from the bottom or side of the evaporator, while the vaporized gas, resembling a swallow stretching its feathers, is discharged from the top.
Several rows of cooling tubes are installed at the top of the shell-and-tube evaporator’s shell body, and gas pockets are welded onto the shell to separate droplets before the gas leaves the evaporator. For large-scale evaporators, specialized separation equipment is typically fabricated.
When a shell-and-tube evaporator is operating, a certain amount of liquid refrigerant must be maintained inside the shell. The liquid level is controlled by a float valve, and the static liquid level height is set according to the diameter of the shell. Most of the cooling tubes are immersed in the liquid, enabling heat exchange through a liquid-to-liquid mechanism. As a result, the heat transfer performance is excellent, and the overall heat transfer coefficient is high. However, please do not allow the liquid level to become too high, as this could lead to liquid backflow into the compressor.
The shell-and-tube evaporators use different tube materials. Generally, ammonia evaporators are made of steel tubes with dimensions 4025×2.5–438×3, while fluorocarbon evaporators are typically constructed using copper or brass tubes. When the brine is corrosive, the tube sheets usually employ corrosion-resistant composite metal plates, and the cooling tubes generally use high-strength aluminum-arsenic brass tubes. To enhance heat transfer performance, fluorocarbon evaporators often utilize finned tubes.
The shell-and-tube evaporator is fabricated by forming two layers of metal sheets through high-pressure gas expansion or mechanical stamping. It can also be produced by die-casting using magnesium-aluminum alloy. This type of evaporator is widely used in small refrigeration equipment such as refrigerators, display cabinets, and ice-cream storage boxes. The flat-tube evaporator made from magnesium-aluminum alloy die-casting is extensively employed in contact freezing applications and is commonly referred to as a flat-tube rapid freezer. The heat transfer coefficient of the shell-and-tube evaporator is higher in liquids than in gases, and it is greater under flowing conditions than under stationary conditions. With its excellent heat transfer performance, compact structure, small footprint, and easy installation, the shell-and-tube evaporator finds extensive application. The structural design of the shell-and-tube evaporator is identical to that of a horizontal shell-and-tube condenser. To maintain an appropriate flow rate, the carrier fluid enters from the lower part of the end cover and exits from the upper part, circulating back and forth both within the evaporating tubes and inside the end covers, thus creating multiple sequential flow paths.
The principles of shell-and-tube evaporators have been introduced above. If you’d like to learn more, feel free to contact us anytime!
Miss Deng:18922776417
Mr. Huang:13450460020
Mr. Zhang:13922978523
Email:1536214764@qq.com/ 673047694@qq.com
Company Address: No. 15, Alley 2, North of Lianhe Road, Fulong Village, Shipai Town, Dongguan City
Copyright © 2021 Dongguan Ganghui Refrigeration & Mechanical Equipment Co., Ltd.
Power by:www.300.cn | SEO | Privacy Policy
Welcome to the official website of GangHui!